Heavy-Duty Electric Pipe & Tube Storage System for Square and Round Stock

A heavy-duty electric pipe and tube storage system holds round, square and rectangular hollow sections in separate tiered compartments and moves them with powered arms instead of forklifts. Herochu rates these racks at 5,000–8,000 kg per level, six tiers high, for 6 m to 12 m stock, with dual-side electric discharge.

Why square and round stock need different rack design

Round tube rolls. Square tube does not. That difference changes how the rack has to be built, and it is why a general-purpose cantilever rack underperforms in a mixed tube store.

A bundle of round tube rests on two contact lines per arm. Arms too far apart and the bundle sags, so the bottom tubes carry everything above them; arms too close and the ends bell out. Square and rectangular hollow section sits flat, stacks on faces, and takes its stiffness from wall thickness and orientation rather than from where the arms touch.

A heavy-duty electric system handles both by treating tier design as a variable. Arm spacing, clear space and arm count are set per compartment, so a bay carrying 168 mm OD pipe does not share geometry with a bay carrying 200 × 200 × 8 mm box.

What “heavy-duty” should mean in a specification

In practice the word means four measurable things:

  • Steel grade. Q235B high-strength steel, with columns sized for the bending moment at the base rather than a nominal tonnage.
  • Crossbar. A dual-beam crossbar ties the column faces together, which stops arms twisting when a bundle lands off-centre.
  • Load per level, stated honestly. 5,000 kg on the 6 m models, 8,000 kg on the 9 m and 12 m models, held across the full tier rather than at one point near the column.
  • Drive sizing. The carriage motor is matched to the extension moment of a loaded arm; a drive sized for an empty arm stalls at half stroke.

Herochu’s electric range is built to those four points, with ISO 9001 manufacturing and CE marking on the drive package.

High-Density Telescopic Cantilever Rack for Round Pipe and Tube Storage
High-Density Telescopic Cantilever Rack for Round Pipe and Tube Storage

Round versus square: what changes on the rack

PropertyRound tubeSquare / rectangular hollow section
Resting behaviourTwo line contacts, will roll if unrestrainedFlat face contact, stable when stacked
Failure mode in storageOvalisation at support points, end damageFace scratching, corner denting, bundle topple if over-stacked
Useful arm spacingLongest practical span to limit sagMatched to bundle width, more arms per tier
Tier clear spaceSet by OD plus sling clearanceSet by stack height, not by single piece
Retrieval riskNeed chocks or end stops on the armNeed straight vertical lift to avoid face damage

Two consequences follow. End stops and arm cradles matter more with round stock, because a slow roll during a lift is how tube ends get dented. Square stock tolerates narrower tier spacing, since nothing needs sling clearance over a curved face, so the same column height yields more usable layers.

The model range

ModelPipe lengthMax. load per levelLevelsClear space
HC-G6055SE6,000 mm5,000 kg5 (customisable)700 mm
HC-G6055E6,000 mm5,000 kg5 (customisable)700 mm
HC-G9068E9,000 mm8,000 kg6 (customisable)700 mm
HC-G12068E12,000 mm8,000 kg6 (customisable)700 mm

Manual versions of the same frame are rated 0.5 t, 1.0 t, 2.0 t or 3.0 t per arm with 1.0–3.0 m extension and 2–6 layers, which suits slow-moving or short-length stock.

Heavy Duty Electric Pipe Storage System for Square Pipes & Round Pipes
Heavy Duty Electric Pipe Storage System for Square Pipes & Round Pipes

What an 8 t tier actually changes

Few plants lift an 8 t bundle daily. They buy 8 t tiers because a 4 t tier forces them to break bundles, and breaking bundles is where the hidden cost sits: extra crane cycles, extra handling, extra labour, more chances to damage material.

With a 5–8 t compartment a full incoming bundle goes from the delivery crane to a tier intact and comes out intact. In Herochu retrofit comparisons for 6 m pipe, retrieval falls from 30–60 minutes to under three, and storage area from around 100 m² of floor to a 20 m² vertical footprint.

Safety case

Crane access removes the forklift from the storage zone, which is the largest single risk reduction in a tube store: forklifts working inside racking are the classic collision and crush scenario. Herochu’s comparison puts accident rate 95% lower after conversion, with material damage close to zero because bundles are lifted, not dragged.

The electric drive adds a second layer. Arm position is set from a pendant, so nobody stands under a partly extended arm to guide it.

How to specify in five questions

  1. Longest stock length, and whether 20 ft or 40 ft containers arrive unbroken.
  2. Heaviest bundle, with sling and spreader included.
  3. Split between round and square stock, so compartments can be allocated.
  4. Number of material types in active circulation — this sets bay count, not pipe count.
  5. Crane hook height and floor slab capacity at the footplates under full load.

Where Herochu fits

Herochu builds the rack, carriage and drive as one system in a 20,000 m² factory with a 300-person team. That matters when tier geometry has to change because a customer’s square stock is deeper than the drawing suggested: the change stays a factory revision. Customisation covers extension length, layer count, clear space, arm rating and column height, set against the real pipe schedule.

Motorized Cantilever Telescopic Pipe Material Rack for Tubes, Pipes & Profiles
Motorized Cantilever Telescopic Pipe Material Rack for Tubes, Pipes & Profiles

Share:

More Posts

Send Us A Message

FAQ

Here are some frequently asked questions about our sheet metal racks and pipe storage solutions. We hope you find them helpful!

Q1: Can I request a custom size or color?
Absolutely. We offer complimentary design services and deliver efficient, tailored solutions to meet your specific requirements.

Q2: Are you a manufacturer or a distributor?
We are a direct manufacturer with over 15 years of industry experience and expertise.

Q3: Is there a minimum order quantity?
No. We welcome orders of any size, starting from a single unit.

Q4: How can I get detailed product information?
Click the “Get a Quote” button to receive product images, detailed specifications, and videos. Our team is always ready to assist.

Q5: How do I provide my storage rack requirements?
Simply share the type, dimensions, and quantity of materials you plan to store, along with any other specific needs. We will develop a professional storage solution for you. Alternatively, leave your contact details for a personalized consultation.

Q6: Do you offer automated loading systems or robotic arms?
Yes. We provide loading robotic arms and integrated loading/unloading systems tailored to your laser cutting machine’s table size and material handling method (e.g., board rack, exchange platform, or material warehouse). Contact us with your details for a customized proposal.

Q7: Do you provide on-site installation and debugging?
Yes. Our technicians can travel to your facility for installation and debugging, ensuring successful operation. We have served clients globally, including in the USA, South Korea, Russia, Qatar, Mexico, South Africa, Egypt, and Lebanon.

Q8: How do you ensure product quality?
Our quality assurance includes:

  • A team of over 40 technical engineers for professional debugging and support.

  • A dedicated quality control department compliant with ISO9001 standards.

  • CE certification for all exports.

  • Rigorous load testing before shipment to ensure structural safety and reliability.

Q9: Where is your factory located?
Our modern 10,000-square-meter manufacturing facility is located in Jiyang Industrial Park, Jinan, Shandong, China.

Q10: How can I evaluate your company’s capabilities?
We offer virtual video factory tours and warmly welcome on-site visits.

Q11: What does your company specialize in?
Jinan Constant Storage Machinery Manufacturing Co., Ltd. is a high-tech enterprise specializing in the R&D, production, sales, installation, and service of intelligent storage solutions. Our product range includes sheet material warehouses, drawer-style shelves, cantilever racks, servo manipulators, gantry loaders, and fully automated handling systems. Supported by a skilled technical team and advanced equipment, we are committed to delivering high-performance storage products and solutions to customers worldwide.

Product Categories

Roll Out Sheet Metal Rack
Roll Out Sheet Metal Rack
Pipe Cantilever Storage Rack
Pipe Cantilever Storage Rack
Sheet Metal Handling Equipment
Sheet Metal Handling Equipment
Automated Sheet Metal Storage Systems
Automated Sheet Metal Storage Systems
Automatic loading and unloading system for laser cutting machines
Automatic loading and unloading system for laser cutting machines

Factory

Factory
Factory
Factory
Factory
Factory

Customers

Sheet material storage Rack
customers2
honor
CONTACT US
Copyright @2025 Jinan Constant Storage Machinery Manufacturing Co., LTD    sitemap
Scroll to Top

✶ ✶ ✶ Get a quote !Email:herochu@sdconstantstorage.com