High-Density Telescopic Cantilever Rack for Round Pipe and Tube Storage

High-density storage usually asks for a trade: the tighter the rack, the harder it is to reach the material in the middle. A honeycomb block packs pipe closely but forces the crane to fish bundles out from between columns. A deep static cantilever bank looks efficient on a layout drawing, but every pick requires the operator to work around the bundles in front, and the effective density collapses under real traffic. A high-density telescopic cantilever rack resolves that trade by making every tier independently addressable from a shared aisle. Density comes from vertical stacking and shared-aisle geometry, not from blocking access.

High-Density Telescopic Cantilever Rack for Round Pipe and Tube Storage

High-density storage usually asks for a trade: the tighter the rack, the harder it is to reach the material in the middle. A honeycomb block packs pipe closely but forces the crane to fish bundles out from between columns. A deep static cantilever bank looks efficient on a layout drawing, but every pick requires the operator to work around the bundles in front, and the effective density collapses under real traffic. A high-density telescopic cantilever rack resolves that trade by making every tier independently addressable from a shared aisle. Density comes from vertical stacking and shared-aisle geometry, not from blocking access.

Herochu builds this system for round pipe and tube storage specifically, and the density gain comes from three mechanisms that compound. The first is tier-level selectivity. Each level has its own telescopic carriage, so a bottom tier holding two-inch OD tubing can extend without disturbing the four-inch OD pipe stored above it. In a static rack, that same pick requires the crane to reach past the upper tiers or the operator to unload the top levels first. The time difference per pick is not dramatic in isolation, but it repeats every time the facility touches a bundle. A service center picking to order may extend tiers dozens of times a day, and at that frequency the selectivity is the difference between a rack that keeps pace with the order desk and one that sets the pace.

The second mechanism is the shared-aisle rail design. Traditional cantilever layouts multiply aisles as storage rows increase. Each row needs its own forklift or crane approach, and the aisle width is dictated by the largest turning radius in the fleet. A Herochu rail-type telescopic system shares a single ground rail between rack rows, so only one aisle is required for simultaneous loading and unloading. The rail is chemically anchored to the slab, which keeps the structure stable under the lateral loads that a crane or a high-bay forklift imposes. The practical result is high-density storage without the row-by-row aisle penalty. The space arithmetic confirms the claim: a 36-meter-long, four-meter-high system with six cantilever levels stores 720 tonnes of steel pipe in 144 square meters, an 80 percent space saving compared with selective pallet racking in the same footprint.

The third mechanism is surface protection as an efficiency variable. Round pipe and tube, especially galvanized conduit, coated tubing, and polished stainless, loses value when the surface is damaged. Floor stacking scratches and deforms material at a rate that turns prime stock into scrap, and every rejected bundle is a rework or scrap cost that never appears in the storage budget. A high-density telescopic cantilever rack with round-pipe saddles and vertical placement reduces that loss because the material is set down onto the arms rather than dragged across them. The telescopic arms extend so the crane can lower the bundle straight down with clear sightlines, eliminating the arm-lip friction that strips coating and scores surfaces on static racks. For a facility handling high-value tube, that damage reduction is a direct efficiency gain: fewer rejected bundles, fewer re-picks, and less material handling that adds no value.

The structural choices support the density claim rather than merely enabling it. The frame is Q235B high-strength steel with a dual-beam crossbar design, and the telescopic sections for pipe cantilevers use seamless round tubing rather than square tubing for smoother travel and more predictable torsional behavior under eccentric pipe loads. Load capacity ranges from 5,000 kg per level on the HC-G6055SE and HC-G6055E to 8,000 kg per level on the HC-G9068E and HC-G12068E, covering six-, nine-, and twelve-meter pipe lengths with layer counts up to six. Carriage speed is 27 mm/s, with 700 mm clear space as standard and dual-side electric assistance for discharge. Those specifications define the operating envelope within which the shared-aisle density calculation holds, because the carriage must move a loaded tier smoothly enough that the operator trusts the system on every pick.

People Also Ask: What makes a telescopic cantilever rack “high-density” compared with a standard cantilever rack?

High density comes from three design choices: vertical stacking across multiple tiers, a shared-aisle rail that serves multiple rack rows, and tier-level telescopic carriages that make every level independently accessible. A standard cantilever rack achieves density by adding rows, but each row needs its own aisle, so the floor space saving is limited. Herochu’s telescopic system shares the aisle and uses the vertical dimension, which is how it reaches an 80 percent space saving compared with selective pallet racking in the same building envelope.

People Also Ask: How does a high-density telescopic rack handle different pipe diameters in the same storage bay?

The tier spacing and arm saddle are configured around the diameter range, and the telescopic carriage works independently per tier. A tier set for small tubing does not interfere with a tier set for larger pipe above it. Herochu’s system allows mixed-diameter storage without the honeycombing that forces a static rack to reserve entire columns for a single product.

People Also Ask: What is the retrieval time for a bundle from a Herochu telescopic cantilever rack?

One operator can pick or replenish an eight-tonne bundle in under two minutes using the electric carriage and an overhead crane. The tier extends at 27 mm/s, locks into position, the crane lifts from clear space, and the tier retracts. The time is consistent across tiers and load weights because the drive moves the carriage at a controlled rate regardless of whether the tier is empty or fully loaded.

FAQ

Here are some frequently asked questions about our sheet metal racks and pipe storage solutions. We hope you find them helpful!

Q1: Can I request a custom size or color?
Absolutely. We offer complimentary design services and deliver efficient, tailored solutions to meet your specific requirements.

Q2: Are you a manufacturer or a distributor?
We are a direct manufacturer with over 15 years of industry experience and expertise.

Q3: Is there a minimum order quantity?
No. We welcome orders of any size, starting from a single unit.

Q4: How can I get detailed product information?
Click the “Get a Quote” button to receive product images, detailed specifications, and videos. Our team is always ready to assist.

Q5: How do I provide my storage rack requirements?
Simply share the type, dimensions, and quantity of materials you plan to store, along with any other specific needs. We will develop a professional storage solution for you. Alternatively, leave your contact details for a personalized consultation.

Q6: Do you offer automated loading systems or robotic arms?
Yes. We provide loading robotic arms and integrated loading/unloading systems tailored to your laser cutting machine’s table size and material handling method (e.g., board rack, exchange platform, or material warehouse). Contact us with your details for a customized proposal.

Q7: Do you provide on-site installation and debugging?
Yes. Our technicians can travel to your facility for installation and debugging, ensuring successful operation. We have served clients globally, including in the USA, South Korea, Russia, Qatar, Mexico, South Africa, Egypt, and Lebanon.

Q8: How do you ensure product quality?
Our quality assurance includes:

  • A team of over 40 technical engineers for professional debugging and support.

  • A dedicated quality control department compliant with ISO9001 standards.

  • CE certification for all exports.

  • Rigorous load testing before shipment to ensure structural safety and reliability.

Q9: Where is your factory located?
Our modern 10,000-square-meter manufacturing facility is located in Jiyang Industrial Park, Jinan, Shandong, China.

Q10: How can I evaluate your company’s capabilities?
We offer virtual video factory tours and warmly welcome on-site visits.

Q11: What does your company specialize in?
Jinan Constant Storage Machinery Manufacturing Co., Ltd. is a high-tech enterprise specializing in the R&D, production, sales, installation, and service of intelligent storage solutions. Our product range includes sheet material warehouses, drawer-style shelves, cantilever racks, servo manipulators, gantry loaders, and fully automated handling systems. Supported by a skilled technical team and advanced equipment, we are committed to delivering high-performance storage products and solutions to customers worldwide.

Customer visit

Herochu has always been adhering to the market-centric approach to meet customer requirements to the maximum extent, and the business philosophy of “creating brands with heart and gaining reputation with sincerity”. It provides customers with high-quality products and services with rigorous military quality, professionalism, and excellence, and has won unanimous praise in the Chinese aerospace, Chinese weapons, Chinese railways, automobile manufacturing, engineering machinery, non-ferrous metal titanium alloy and other industries.

customers

Factory

Factory
Factory
Factory
Factory
Factory
customers2
honor

Hot Selling Machines

Product Categories

Roll Out Sheet Metal Rack
Roll Out Sheet Metal Rack
Pipe Cantilever Storage Rack
Pipe Cantilever Storage Rack
Sheet Metal Handling Equipment
Sheet Metal Handling Equipment
Automated Sheet Metal Storage Systems
Automated Sheet Metal Storage Systems
Automatic loading and unloading system for laser cutting machines
Automatic loading and unloading system for laser cutting machines
Scroll to Top

✶ ✶ ✶ Get a quote !Email:herochu@sdconstantstorage.com