Electric Drawer Roll Out Sheet Metal Rack

An electric drawer roll out sheet metal rack stores sheet on powered trays that extend clear of the frame at the push of a button. Herochu rates these drawers from 3,000 kg to 20,000 kg per level, covering 1.5 m blanks through 12 m heavy plate, with five or six tiers and electric-assist discharge.

Electric Drawer Roll Out Sheet Metal Rack

An electric drawer roll out sheet metal rack stores sheet on powered trays that extend clear of the frame at the push of a button. Herochu rates these drawers from 3,000 kg to 20,000 kg per level, covering 1.5 m blanks through 12 m heavy plate, with five or six tiers and electric-assist discharge.

How a roll out drawer works

Each tier carries a pallet on guides inside the frame. A drive unit moves that pallet horizontally until the stack sits outside the rack line, in open air, at a comfortable working height.

The mechanism is simple, and the consequences are not. Once the pallet leaves the frame, the crane has vertical clearance above the sheet, the sling has room to hang, and the operator can see the sheet edge without stepping into the rack.

Electric drawer or manual crank: the real differences

Both systems move a pallet out of a rack. The gap between them is load rating, effort and where the operator stands.

Load rating. A manual crank rack is practical to roughly 5,000 kg per level, because a person is turning the drive. Herochu’s electric drawers run to 20,000 kg on the 12,000 mm platform, where no hand drive would be sensible.

Effort and speed. A crank handle on a 6 m drawer carrying 5,000 kg is slow work, with stops to reposition hands. Powered extension runs at up to 5.27 m/min from a handset.

Operator position. This is the safety argument that rarely appears in brochures. Manual extension puts a person beside a loaded pallet, pushing against a handle. Electric extension puts that person two metres back with a remote. The table sets out where the two systems separate in daily use.

| Criterion | Manual roll out rack | Herochu electric drawer | | Typical load per level | Up to about 5,000 kg | 3,000 to 20,000 kg by model | | Extension method | Crank handle at the rack face | Remote-controlled drive | | Operator position | Beside the load | Clear of the drawer path | | Long sheet handling | Slow, two-person job at 6 m and above | One operator plus crane | | Best fit | Low picks, lighter sheet | Daily picks, heavy plate, long formats |

Where the powered drawer earns its cost

The purchase price is higher than a manual unit, and the difference is recovered through the work it removes: crane hook time, second operators, sheet damage and the restacking loop.

The case is strongest where picks run all shift, where cranking distance becomes the bottleneck on 6 m and 12 m drawers, where surface marks turn aluminum into scrap, and where one person runs the storage area alone.

Space saving: one aisle serves every tier

The drawer occupies aisle space only while it is open. Between picks, the rack is a solid block and the aisle stays clear for the crane, a forklift or a walkway.

Cantilever storage needs clearance at every level for the crane to approach and the sheet to swing. A six-tier drawer bay needs one aisle for six tiers, and the crane never threads between arms.

Sheet protection

Sheet metal loses value at the edges first. A drawer keeps the stack on its own pallet, so nothing slides across the sheet below and no magnet drags a top sheet out from under the pile.

Keep the stack inside the pallet edge so nothing overhangs into the frame, use a non-marking deck and separators for aluminum and stainless, and keep the pallet surface clean. Grit trapped under a 3 tonne stack marks every sheet above it.

Technical parameters

| Model | Sheet size | Tiers | Load per level | Pallet speed | | HC-B3015E-63 | 3,000 x 1,500 mm | 6 | 3,000 kg | 2.97 m/min | | HC-B4015E-63 | 4,000 x 1,500 mm | 6 | 3,000 kg | 2.28 m/min | | HC-B4020E-63 | 4,000 x 2,000 mm | 6 | 3,000 kg | 5.27 m/min | | HC-B6015E-65 | 6,000 x 1,500 mm | 5 | 5,000 kg | Model dependent | | HC-B12025E-520 | 12,000 x 2,500 mm | 5 | 20,000 kg | Model dependent |

Clear space is 120 mm and customizable, discharge uses electric assistance, and the frame is welded Q235B with dual-beam crossbars under each pallet.

Choosing between the five models

Start with the largest sheet the plant will store over the next five years, not the average sheet moving through today. The 3,000 mm platform handles laser and plasma blanks and general fabrication. The 4,000 mm models cover panel work, with the 2,000 mm width for wide plate. The 6,000 mm unit is the standard choice for mill plate. The 12,000 mm platform is for heavy fabrication where a single sheet can weigh several tonnes.

Then set tier count against the number of grades and thicknesses in stock. Six tiers on a 3,000 kg model gives 18 tonnes of separated storage in one bay. Herochu quotes tier count and clear space against the load schedule.

FAQ

What is the difference between a motorized and a manual roll out sheet metal rack? A motorized rack extends its drawers under electric power from a remote and carries up to 20,000 kg per level on the largest platform. A manual rack uses a crank handle, typically with a ceiling around 5,000 kg per level, and needs the operator at the rack face during extension.

Can one person retrieve a sheet? Yes, for the storage step. One operator selects the tier, the drawer extends, and the crane lifts the sheet. The second person who would hold and guide a manual drawer is no longer needed.

What sheet sizes does it take? From 3,000 x 1,500 mm to 12,000 x 2,500 mm across five models, with five or six tiers and 120 mm clear space as standard.

A drawer is a handling decision

The rack itself is straightforward steel. The decision worth studying is how the sheet leaves storage, because that is where labour, damage and crane time accumulate. An electric drawer moves that moment into open air, and Herochu sizes the frame, drive and tier clearances around the plate a plant actually stores.

FAQ

Here are some frequently asked questions about our sheet metal racks and pipe storage solutions. We hope you find them helpful!

Q1: Can I request a custom size or color?
Absolutely. We offer complimentary design services and deliver efficient, tailored solutions to meet your specific requirements.

Q2: Are you a manufacturer or a distributor?
We are a direct manufacturer with over 15 years of industry experience and expertise.

Q3: Is there a minimum order quantity?
No. We welcome orders of any size, starting from a single unit.

Q4: How can I get detailed product information?
Click the “Get a Quote” button to receive product images, detailed specifications, and videos. Our team is always ready to assist.

Q5: How do I provide my storage rack requirements?
Simply share the type, dimensions, and quantity of materials you plan to store, along with any other specific needs. We will develop a professional storage solution for you. Alternatively, leave your contact details for a personalized consultation.

Q6: Do you offer automated loading systems or robotic arms?
Yes. We provide loading robotic arms and integrated loading/unloading systems tailored to your laser cutting machine’s table size and material handling method (e.g., board rack, exchange platform, or material warehouse). Contact us with your details for a customized proposal.

Q7: Do you provide on-site installation and debugging?
Yes. Our technicians can travel to your facility for installation and debugging, ensuring successful operation. We have served clients globally, including in the USA, South Korea, Russia, Qatar, Mexico, South Africa, Egypt, and Lebanon.

Q8: How do you ensure product quality?
Our quality assurance includes:

  • A team of over 40 technical engineers for professional debugging and support.

  • A dedicated quality control department compliant with ISO9001 standards.

  • CE certification for all exports.

  • Rigorous load testing before shipment to ensure structural safety and reliability.

Q9: Where is your factory located?
Our modern 10,000-square-meter manufacturing facility is located in Jiyang Industrial Park, Jinan, Shandong, China.

Q10: How can I evaluate your company’s capabilities?
We offer virtual video factory tours and warmly welcome on-site visits.

Q11: What does your company specialize in?
Jinan Constant Storage Machinery Manufacturing Co., Ltd. is a high-tech enterprise specializing in the R&D, production, sales, installation, and service of intelligent storage solutions. Our product range includes sheet material warehouses, drawer-style shelves, cantilever racks, servo manipulators, gantry loaders, and fully automated handling systems. Supported by a skilled technical team and advanced equipment, we are committed to delivering high-performance storage products and solutions to customers worldwide.

Customer visit

Herochu has always been adhering to the market-centric approach to meet customer requirements to the maximum extent, and the business philosophy of “creating brands with heart and gaining reputation with sincerity”. It provides customers with high-quality products and services with rigorous military quality, professionalism, and excellence, and has won unanimous praise in the Chinese aerospace, Chinese weapons, Chinese railways, automobile manufacturing, engineering machinery, non-ferrous metal titanium alloy and other industries.

customers

Factory

Factory
Factory
Factory
Factory
Factory
customers2
honor

Product Categories

Roll Out Sheet Metal Rack
Roll Out Sheet Metal Rack
Pipe Cantilever Storage Rack
Pipe Cantilever Storage Rack
Sheet Metal Handling Equipment
Sheet Metal Handling Equipment
Automated Sheet Metal Storage Systems
Automated Sheet Metal Storage Systems
Automatic loading and unloading system for laser cutting machines
Automatic loading and unloading system for laser cutting machines
Scroll to Top

✶ ✶ ✶ Get a quote !Email:herochu@sdconstantstorage.com